X Clean-Trace 3M Water ATP 3M Test Swab (AQF100x) 100 Pack, Dated 2025-01-03

Product details (archived)

The information below is retained for reference only. This item is discontinued and cannot be ordered.

3M Clean-Trace Water Plus Total ATP (AQF100x) 100 Pack, Dated 2025-01-03

3M™ Clean-Trace™ Water ATP test is a single-use test device that contains sample collection rings for the collection of an aqueous sample (figure 1). The sample collection rings are coated with a wetting agent to aid in the collection of a liquid sample without the release of Adenosine Tri-Phosphate (ATP) from intact microbial cells. Upon activation of the test device, reagent in the cuvette of the test device reacts with ATP collected on the sample collection rings to produce light. The intensity of the light is proportional to the amount of non-microbial ATP. Measurement of the light requires the use of a 3M™ Clean-Trace™ NG Luminometer and the results are displayed in Relative Light Units (RLU). The test kit contains 100 ready to use test devices packaged as units of 10 per individual foil pouch.

Real-time ATP water hygiene test gives an objective indication of cleanliness in seconds.

• Simple to use and ideal for busy production environments.
• Rapid results allow immediate corrective action.
• The test is designed to rapidly assess equipment sanitation processes and the efficiency of Clean In Place (CIP) procedures by the improved and more accurate detection of organic contamination from microbial or product residues.
• The test gives an objective indication of cleanliness in water samples in seconds.
• ECCN: EAR99.
• Harmonized Code: 3822005090.
• 3M Stock #: 7100067522.
• Previous 3M Stock # GH620522819.
• 3M Catalog #: AQF100.
• UPC #: 00707387579906.

Results measured using the 3M Clean-Trace NG or LM1 Luminometer and provided in Relative Light Units (RLU).

• Optimal test temperature: 59° to 86° F (15° to 30° C).
• Shelf life (approximate):
  • Refrigerated 35.6° to 46.4°F (2°C to 8°C): 10 months.
  • Room temperature 69.8° to 77°F (21°C - 25°C): 2 months.

Click to Download Safety Data Sheet - SDS

Instructions for Use

1. Before the 3M Clean-Trace test device is activated, it is important to ensure your 3M Clean-Trace NG or LM1 Luminometer is switched on and initialized. Refer to the manual provided with the instrument for full details. Place the 3M Clean-Trace test devices at room temperature for at least 10 minutes before use.
2. Collect liquid samples from the test sites of interest. Process each sample through steps 3-6. DO NOT batch at any of these stages.
3. Swirl to mix the sample. Remove a 3M Clean-Trace test device from the foil pouch. Remove the sampling stick from the 3M device and immerse the sample collection rings into the liquid under test, tapping the handle gently if bubbles form (figure 1). Immediately remove the sample head from the solution to be tested and carefully return the sampling stick to the test device such that the handle is at its starting position.
4. To process the sample, push down firmly on the top of the 3M Clean-Trace sample stick handle (figure 2). The handle will slide into the test device tube and the top of the handle should be level with the top of the device tube when fully depressed. Grip the top of the test device and shake rapidly side-to-side for at least five seconds to mix the sample and reagent (figure 3).
5. Immediately open the sample chamber of the 3M Clean-Trace NG or LM1 Luminometer and insert the 3M Clean-Trace test device. Close the chamber cap and press the measure button. The light emitted by the 3M Clean-Trace test device will be measured and the result (in RLU) will appear on the display (figure 4).