Versa-Test Heat Detector Tester Kit (VT694-16) w/16' Telescoping Pole

Product details (archived)

The information below is retained for reference only. This item is discontinued and cannot be ordered.

Versa Test Heat Detector Test Kit with 8 foot (96 inches) Fiberglass Telescoping Extension Pole and Heavy Duty Carry Bag.

The HEAT DETECTOR TESTER™ functionally tests ALL mechanical and electronic self-restoring, fixed temperature and rate-of-rise, or rate-compensated heat detectors in the 135 to 190 degree Fahrenheit range. Finally, dispense with Ladders, Heat Lamps, Hair Dryers, Extension Cords etc. Use the Versa Poles to reach as high as 30 feet.

The Head Pad, when wetted with the provided Saline Solution (Non Hazardous Material), will generate the heat needed to activate the heat detector. The Heat Pad will typically last about 5-15 minutes* (at times as much as 20-25 minutes) by simply repeating these water applications.

* Times are approximate since ambient temperature and conditions will effect the Heat Pads length of time to maintain temperatures.

Heat Detector Testing Kit Contains:

• (1) 16' Telescoping Fiberglass Versa Test Pole
• (1) Versa Test Pole Adapter
• (1) HA94 Heat Pad Container
• (1) HC94 Tray
• (1) HO94 Applicator.
• (2) SS94 Saline Solution
• (4) HP94 Heat Pads (Saline Solution Activated)
• (1) VTB1 Equipment Bag

Link to refills

Use any Versa Test poles with this kit. For added reach you can add a VP-4X extension

• Kit with 8' extension VT-694-8
• Kit without extension pole VT-694

Instructions:

1. Heat Pads are manufactured 4 pads to a sheet. 2 pads are required to perform an adequate test. Carefully cut the sheet of heat pads in half, and place 2 pads (1/2 of sheet) on the V placing ends of pad underneath rubber bands (see illustration, 1a).
2. Place V holding pads onto cup. Attach cup to adapter and slide adapter in to telescoping test pole.
3. Using applicator provided, measure 2 tablespoons of saline solution and douse the 2 pads attached to V.
4. Heat Pads will activate with in 30 seconds after Saline Solution is applied, as discussed below. Heat Pads may be reactivated up to 3 times.
5. Do not remove Heat Pads from their plastic bag until ready for use.
6. In all test, the heat detector should alarm within 10 to 15 seconds. If it does not, and after you have determined that the Heat Pad is still hot – the heat
   detector or the fire alarm system is not fully operation.
7. Save any Saline solution for the next testing by simply folding the top of the plastic pack and putting tape over the top of the pack
8. Spent heat pads and empty saline solution packs may be safely disposed of in any waste container.

Click to Download Safety Data Sheet - SDS

Other HSI Versa-Test, SOLO and TestiFire Kit Combinations

Model Number	Smoke Testing	Heat Testing	CO Testing	Access Height+	Detector Removal	Case Included
VT-ED8	*	-	**	12 feet	-
VT-ED16	*	-	**	20 feet	-
VT-KIT1	*	-	**	24 feet	-
VT-COMPLETE	*		**	24 feet	-
VT-694-8	-		-	12 feet	-
VT-694-16	-		-	20 feet	-
SDI Fire SOLO and TestiFire
SOLO 808 KIT	*	-	**	12 feet	-
SOLO 809 KIT	*	-	**	20 feet	-
SOLO 810 KIT	*	-	**	10 feet	-
SOLO 818 KIT	-		-	12 feet	-
SOLO 819 KIT	-		-	20 feet	-
SOLO 820 KIT	-		-	10 feet	-
SOLO 850 KIT	*	-	**	24 feet
SOLO 851 KIT	*		**	24 feet
SOLO 823 KIT	*		**	30 feet
SOLO 900 KIT		-	-	30 feet	-
TF2851				24 feet
TF2823				30 feet